| Type | Portable | Butane |
|---|---|---|
| Heating | Convection | Convection |
| Heat-up time | 3s | N/A |
Green = better value
Open in full comparison →Dreamwood Glow RCV 18 Classic V3 is a portable dry-herb vaporizer. VapoChecker compares current offers from 158 € (plus shipping) across 1 shop (as of Nov 22, 2026).Price basis: Item price excluding shipping and coupons
158.00 € at La Centrale Vapeur · Compare prices| Heating Method | Convection |
| Device Type | Portable |
| Brand | Dreamwood |
| Power Source | 510 Mod |
| Heat-up Time | 3 seconds |
| Water Pipe Compatible | View water pipe adapters |
| Session Mode | On-Demand |
| Temperature Control | Analog (Dial) |
| Material | Dry Herb |
| Vapor Path | Glass |
| Charging Port | USB-C |
Specification sources: greendream.shop / en/p/glow-rcv-18-brazilian-pear-dreamwoodManufacturer
Dreamwood sells the device as the Glow RCV 18 V3 and describes it as a further development of its Rebuildable Convection Vaporizer.
Heating is done via on-demand convection with hot air. The heating element is a replaceable double-coil system made of Kanthal A1. The manufacturer states a power range of 30 to 80 watts and recommends starting at 35 watts. According to Dreamwood, the Glow is ready to use in about 3 seconds. Dreamwood Vaporizer is based in Duisburg and, according to their own statement, has been crafting vaporizers from fine wood since 2015. According to their terms and conditions, every product is a handcrafted individual piece.
Dreamwood Glow RCV 18 Classic V3 is a convection vaporizer for dry herbs that screws onto a battery (box mod) with a 510 thread; Dreamwood sells it as the Glow RCV 18 V3. Heating is provided by a replaceable double-coil heating element made of Kanthal A1, operating at 30 to 80 watts. According to the manufacturer, the Glow is ready to use in approximately 3 seconds. The cover is made of fine wood, and each piece is a handcrafted, one-of-a-kind item.
See also: Dreamwood Punch · Dreamwood Dobby · Dreamwood Glow · Dreamwood DLX
The Glow consists of the base deck with the 510 thread, the wood cover, and the mouthpiece. The herb chamber sits directly in the mouthpiece, which is available in either wood or glass; according to Dreamwood, this makes cleaning and filling easier. The base deck features an airflow ring that allows you to adjust the draw resistance.
Dreamwood lists fine wood, stainless steel, and silicone as materials; pieces with a glass mouthpiece also include borosilicate glass. The type of wood is listed on the respective product page, for example Osage, Olive, or Santos Rosewood. According to the manufacturer's terms and conditions, every product is a handcrafted individual piece made from natural wood. Color, grain, and texture therefore vary from piece to piece. For wood care, Dreamwood recommends its DynaWax.
Dreamwood describes the system as on-demand convection (hot air extraction). The heating element is a replaceable double-coil system made of Kanthal A1 Mix Twisted. Power is supplied by a battery mod with a 510 thread, onto which the Glow is screwed. The manufacturer specifies a power range of 30 to 80 watts and recommends starting at 35 watts. Intensity is adjusted via the wattage on the battery mod; Dreamwood does not state a temperature in degrees. Thanks to the double-coil heating element, the Glow is ready to use in about 3 seconds according to the manufacturer.
For operation, Dreamwood lists safety instructions: use only quality batteries with a minimum discharge rate of 20 A, and do not use coils below 0.10 ohms. The battery mod must be switched off before every coil change and before any maintenance work. Never touch the heating coil while the device is switched on or immediately after it has fired. The manufacturer assumes prior experience with box mods and electronics.
The instructions on the product page describe the process as follows:
If the wood cover fits too tightly, Dreamwood recommends applying a little DynaWax to the inner edge or the O-rings.
According to Dreamwood, the box includes the Glow RCV 18 V3 with base deck, wood cover, and mouthpiece, a tool set with screwdriver and tweezers, as well as a spare parts set with replacement screws, a replacement heating element, O-rings, and screens. A battery mod is not included. Engraving of the Dreamwood logo is available upon request.
The heating element is not permanently installed and can be replaced when needed or swapped out for custom coil builds. As spare parts for the Glow RCV, Dreamwood carries among other things a single coil heater made of Kanthal A1 and a double coil heater made of stainless steel. Also available separately are stainless steel mesh pods with a 12.5 mm diameter that can be pre-loaded and swapped out on the go, dome screens with 12.5 mm, and a short borosilicate glass mouthpiece with a length of 80 mm.
Dreamwood does not state a warranty period either on the product page or in its terms and conditions.
| Type | Portable | Butane |
|---|---|---|
| Heating | Convection | Convection |
| Heat-up time | 3s | N/A |
Green = better value
Open in full comparison →A convection vaporizer for dry herbs by Dreamwood Vaporizer that is screwed onto a battery mod with a 510 thread. The manufacturer sells it as the Glow RCV 18 V3. RCV stands for Rebuildable Convection Vaporizer.
A box mod with a 510 thread. According to Dreamwood, the Glow operates at 30 to 80 watts, with a recommended starting point of 35 watts. The manufacturer requires quality batteries with a minimum discharge rate of 20 A and warns against coils below 0.10 ohms. A battery mod is not included in the package.
Dreamwood does not specify a temperature in degrees. Wattage is adjusted on the battery mod: start at approximately 35 watts and increase in steps of 5 watts if vapor production is insufficient. According to the manufacturer, the power range goes up to 80 watts.
According to Dreamwood, in about 3 seconds. The instructions recommend pressing the power button, preheating for 2 to 3 seconds, and then inhaling steadily for 5 to 10 seconds.
The Glow RCV 18 V3 with base deck, wood cover, and mouthpiece, a tool set with screwdriver and tweezers, and a spare parts set with replacement screws, a replacement heating element, O-rings, and screens. A battery mod must be purchased separately.
Yes. The double-coil heating element made of Kanthal A1 is not permanently installed and can be replaced or swapped out for custom coil builds. A replacement heating element is included. The battery mod must be switched off beforehand, and the heating coil must not be touched while the device is on or immediately after it has fired.
Comments
No comments yet. Be the first!
Sign in to comment