MAD Heaters TEMPEST 2 — Black - Aqua (Ti)

No offers right now
Available now: MAD Heaters TEMPEST 2 → from 204.73 €

Pros

  • Grade-5 titanium with a replaceable heat shield
  • Jet flame or induction (Wand, YLL 3.0)
  • Chamber in three sizes from 0.1 to 0.2 g
  • WPA-compatible with 10, 14 and 18 mm

Cons

  • No heat-up time for the jet flame from the manufacturer
  • No temperature reading for the vapor
  • Manual adjustment of the heat source required

No prices currently available

No shop prices are currently available for this vaporizer. Please check back later.

View alternatives →

Specifications

Heating Method Convection
Device Type Ball Vape
Brand MAD Heaters
Power Source Butane/Flame
Weight 46 g
Dimensions 12.2 x 1.85 x 1.85 cm
Warranty 1 year
Water Pipe Compatible View water pipe adapters
Session Mode On-Demand
Temperature Control Manual
Material Dry Herb
Vapor Path Glass
Charging Port Not needed (no battery)

Manual & datasheet

Key Facts — MAD Heaters TEMPEST 2 Black - Aqua (Ti) Butane · Heating: Convection · Weight: 46g
Read the full description

Three chamber positions, a visual indicator, and two click discs enable different heating and draw profiles. MAD Heaters lists WPA compatibility with 10 / 14 / 18 mm as well as the iSpire Wand and YLL 3.0 as suitable induction heaters. A universal heating time or digitally measured material temperature has not been published. You can find current offers in the TEMPEST 2 price comparison.

About this vaporizer

MAD Heaters TEMPEST 2 is a ball vape made of grade-5 titanium with no battery, whose heat is stored by zirconium oxide balls. It is heated with a jet flame or induction heater; for titanium caps with zirconia in the YLL 3.0 at 80 watts, MAD Heaters quotes 35 to 40 seconds. The chamber can be set to approximately 0.1, 0.15 or 0.2 g, and WPA connections are available for 10, 14 and 18 mm.

See also: Tempest 2 Slim · TEMPEST 2 Black - Lime Green · TEMPEST 2 Black - Purple · TEMPEST 2 All Black (Ti)

TEMPEST 2 Specifications at a Glance

FeatureTEMPEST 2
Heating methodConvection-heavy ball vaporizer
Heat sourceSuitable jet flame or compatible induction heater
MaterialGrade-5 titanium; stainless steel on the induction sleeve, indicator housing, and screens
Heat ShieldAluminum, wood, or titanium on appropriately labeled variants
Dimensions122 mm long × 18.5 mm diameter
Weight46 g with aluminum Heat Shield; 43 g with wood; no weight published for titanium Heat Shields
Heat-up timeDepends on the setup; for example, 80 W for 35–40 s with a titanium Cap and zirconia in the YLL 3.0
TemperatureNo measured digital material temperature; two click discs and a visual indicator
ChamberApproximately 0.1 / 0.15 / 0.2 g, three screen positions
Water filterWPA compatibility: 10 / 14 / 18 mm
Manufacturer warrantyOne year under the current MAD Heaters policy unless otherwise stated on the product page

Source for heating settings: TEMPEST 2 manual.

← Back to Overview

Frequently asked questions

A ball vape uses thermal media for heat storage. MAD Heaters describes the TEMPEST 2 as convection-heavy with zirconia balls. This does not mean that every configuration heats exclusively through convection.

The manual recommends a dual-, triple-, or medium-sized single-flame torch. Hold the tip of the flame approximately 1 cm away from the cap, rotate the device slowly, and never heat the indicators directly. Alternatively, the iSpire Wand and YLL 3.0 are documented. Before purchasing, check the opening of the Ispire The Wand: MAD Heaters notes that some Ispire The Wand devices are too narrow for the TEMPEST 2. The opening must be at least 14.0 mm wide. If the cap fits in the glass without any play, this combination should not be used because the glass may break when heated. Its general listing as a compatible heater therefore does not replace checking the specific device. Notice from the TEMPEST-2 manufacturer.

The TEMPEST 2 has its own chamber and heating head. The manufacturer's approval for the iSpire Wand and YLL 3.0 is not a blanket confirmation that arbitrary DynaVap tips or third-party accessories will fit. Before purchasing, check the opening of the Ispire The Wand: MAD Heaters notes that some Ispire The Wand devices are too narrow for the TEMPEST 2. The opening must be at least 14.0 mm wide. If the cap fits in the glass without any play, this combination should not be used because the glass may break when heated. Its general listing as a compatible heater therefore does not replace checking the specific device. Notice from the TEMPEST-2 manufacturer.

Depending on the screen position, approximately 0.1 g, 0.15 g, or 0.2 g. The corresponding volume levels are 0.6 / 0.9 / 1.2 cm³; the actual mass depends on the material and how the chamber is filled.

There is no universal heat-up time. For example, for titanium caps with zirconia in the YLL 3.0 starting at room temperature, the manual specifies 80 W for 35–40 s. With a warm cap, it takes 8–12 s less at the same wattage. When using a torch, the click discs and visual indicator provide guidance.

The product page states WPA compatibility with 10 mm, 14 mm, and 18 mm. Check the actual fit of the water filter and your specific version.

The main construction is made of Grade-5 titanium. The induction sleeve, indicator housing, indicators, and screens contain stainless steel. Depending on the specified model, the Heat Shield is made of aluminum, wood, or titanium; the standard balls are zirconia.

The TEMPEST 2 is documented as having three chamber positions, visual and audible indicators, and compatibility with the Wand and YLL 3.0. Compare the actual heating and accessory configurations of both devices; no measured equivalence in flavor is claimed here. Before purchasing, check the opening of the Ispire The Wand: MAD Heaters notes that some Ispire The Wand devices are too narrow for the TEMPEST 2. The opening must be at least 14.0 mm wide. If the cap fits in the glass without any play, this combination should not be used because the glass may break when heated. Its general listing as a compatible heater therefore does not replace checking the specific device. Notice from the TEMPEST-2 manufacturer.

For the balls, the manual describes a separate cleaning procedure after approximately 300 Bowls using a suitable torch or, alternatively, a concentrated degreasing cleaner. Do not expose glass media to extreme heat. Follow all of the manufacturer's instructions regarding materials, cooling, and reassembly.

MAD Heaters sells screens, balls, Heat Shields, and parts of the heating head separately, among other items. Availability and compatibility depend on the specific version; the individual product description is authoritative.

The current MAD Heaters policy specifies a one-year manufacturer's warranty covering defects in materials and workmanship under normal use, unless otherwise stated on the product page. Misuse, accidents, modifications, and normal wear and tear are excluded.

The manual specifies suitable dried plant material. It does not state that waxes, liquids, or arbitrary concentrates are approved for use; therefore, we do not add such a suitability claim.

The manufacturer does not specify a general service life or a documented time frame for microcracks. The balls are replaceable; cleaning, mechanical stress, and the ball material affect their condition.

Experiences & discussion

No reviews or comments yet. Share your experience

Comments

No comments yet. Be the first!

Loading...
Scroll to Top