Tinymight 2

The Tinymight 2 features an analog temperature dial on the bottom panel. It offers 10 main steps with half-steps in between, providing approximately 20 different temperature settings across a range of 120 to 240°C.

The electronics control the heater in real time with high precision. The set temperature is maintained reliably regardless of draw strength.

Calibration:

If the default temperature range isn't ideal, the Tinymight 2 can be calibrated in steps from -3 to +3 relative to factory settings. Calibrating to +3 means that setting 7 delivers the same results as setting 10 normally would. Detailed instructions are available in the Tinymight 2 Manual (PDF).

Note: The Tinymight won't turn on if the dial is set below level 2 – this is a safety feature to prevent accidental activation.

The Tinymight 2 uses a stainless steel convection heater with an exceptionally large surface area. Unlike most portable vaporizers, the Tinymight works with pure convection: air is drawn through the heating element during inhalation and then passes through the material.

Benefits of pure convection:

• Better flavor: The large heating surface means lower surface temperatures are needed, resulting in purer taste
• No residual heating: In on-demand mode, heating stops immediately when the button is released
• Even extraction: Hot air flows evenly through the material

The heating element is a spiral-shaped metal structure. Different production runs have used various configurations – some placed inside a glass tube, others inside a metal tube, and some as a free-standing structure with ceramic support rods.

Note: The heater produces a faint noise during operation. This is normal and results from current pulses acting on the lightweight, large-surface heating structure.

The Tinymight 2 uses a replaceable 18650 lithium-ion battery. One Molicel battery is included in the package.

Compatible batteries:

The Tinymight 2 is very powerful and requires high-drain cells. Only the following Molicel models are recommended:

• Molicel P30B (3,000 mAh)
• Molicel P28A (2,800 mAh)
• Molicel P26A (2,600 mAh)

Warning: Other 18650 batteries may provide insufficient performance or pose a safety risk. Only use original batteries or Molicel cells from trusted sources.

Charging:

Charging is done via USB with a cable and an adapter capable of at least 2A output. A full charge from 0 to 90% takes approximately 1.5 hours. The aluminum bottom panel gets warm during charging – this is normal as it acts as a heatsink.

Charging only starts when the battery voltage has dropped sufficiently. If charging doesn't begin, the battery is still too full for a new charging cycle.

The Tinymight 2 offers two operating modes, selectable when turning on the device:

On-Demand Mode:

In on-demand mode, the vaporizer heats only while the button is held down. Upon release, the device returns to standby immediately. Heat-up time is approximately 3 seconds.

• Perfect for single draws between tasks
• No material consumption during standby
• Maximum control over extraction

Session Mode:

In session mode, the vaporizer heats up automatically and maintains a stable temperature until turned off.

• Ideal for longer sessions
• Constant temperature without holding the button
• Easy to pass around in a group

Micro-dosing: The Tinymight 2 works excellently for micro-dosing. The adjustable chamber volume works well with very small amounts as well as larger loads.

Regular cleaning is important for vapor quality and longevity of the Tinymight 2. The parts that need cleaning are the glass tube with cooling unit and occasionally the stainless steel mesh screen above the heater.

Glass tube & cooling unit:

1. Unscrew the threaded ring on the front panel – the internal parts slide out easily
2. Rinse the glass tube and cooling unit with hot water and detergent
3. Alternatively, soak in isopropyl alcohol for stubborn residue
4. Rinse thoroughly and allow to dry completely

Stainless steel mesh screen:

The mesh screen above the heater protects the heating element. If dirty, it can be gently cleaned with the included brush.

Important: The mesh screen must always sit securely in its holder. If it falls onto the heater, it can cause a short circuit that damages the heater. Do not use third-party dosing capsules that could displace the screen.

The Tinymight 2 is handcrafted in Helsinki, Finland. Each unit is individually assembled and assigned a unique serial number.

Materials in the vapor path:

• Stainless steel – heating element and vapor channel
• Quartz glass – glass lining and vapor tube

The entire vapor path uses no glues, chemicals, or insulation materials. The only materials in the device are oak wood, stainless steel, glass, and aluminum. The electronics board is separated from the vapor path.

Counterfeit detection:

Counterfeits exist on the market. Original units from February 2022 onwards have a serial number on the bottom panel and an individually registered security code. In fake TM2 units, the battery is often inserted the opposite way – the original has "+" printed on the inside of the battery lid.

Reduced vapor production:

1. Check the battery: A weak or old battery can reduce performance. Only use recommended Molicel cells.
2. Clean battery lid contact: Occasionally scratch the contact point on the battery lid to ensure optimal power transfer.
3. Adjust calibration: The temperature range can be adjusted in steps from -3 to +3. At +3, setting 7 delivers the results of setting 10.

Cracked glass lining:

The internal glass lining can crack if the unit is dropped. Replacement glass linings are available from the Tinymight shop. Replacement requires a Torx T20 screwdriver. Warning: The internal screw must be loosened before removing the top panel – otherwise the device will be destroyed.

Cooling unit slides out of glass tube:

The cooling unit requires two different o-rings: one 10mm and one 11mm ring. If both are the same size, the fit will be too loose or too tight.

Over 90 official accessories and spare parts are available for the Tinymight 2. Compare prices from 11 European shops in our Tinymight price comparison. The full range is also available directly from the Tinymight EU Shop.

Glass Tubes & Stems:

Mouthpieces:

• Glass Mouthpiece for Ball Stems – fits Long and Short Ball Stem
• Colored Mouthpieces (Pink, Smokey) – glass, for individual style

Dosing Capsules:

• Dosing Capsule v2 – stainless steel, for clean and quick loading
• Dosing Capsule v2 TITANIUM – lighter and more durable
• 5-pack with holder – practical for on-the-go use (stainless steel or titanium)

Water Pipe Adapters:

• 14mm glass adapter – for 14mm water pipes
• 18mm glass adapter – for 18mm water pipes
• 3-in-1 adapter – compatible with various sizes
• Portable Bubbler – compact water filter for on the go

Spare Parts:

• Glass Lining – replacement for cracked linings after drops
• Screen Holder – holds the heater protection screen
• Mesh Screen – protects the heater element
• Tube Holder Threaded Ring – secures the glass tube
• O-rings – sets for cooling unit, ball stems, top panel and multitool

Other Accessories:

• Cooling Unit – most important wear part
• Stir Tool / Multitool – for stirring and emptying the chamber
• Extra Battery + Charger – for unlimited runtime on the go
• USB-C Quick Charger (EU plug) – for fast charging
• Beeswax Jar – for wood surface maintenance
• Bag of Balls – replacement glass balls for ball stems

The Tinymight 2 package includes:

• 1× Tinymight 2 Vaporizer (oak wood body)
• 1× Molicel 18650 battery
• 1× Glass tube with cooling unit
• 1× USB charging cable
• 1× Cleaning brush
• 1× Spare o-rings
• 1× Quick start guide

Note: Additional glass tubes, replacement glass linings, and extra Molicel batteries are available as optional accessories directly from Tinymight.

Choosing the right temperature on the Tinymight 2 determines flavor, vapor density, and active compound profile. Lower temperatures (170–185 °C) emphasize terpenes and deliver mild, aromatic vapor. Higher temperatures (195–210 °C) produce thicker clouds and stronger effects.

Temperature Zones

Practical Tips

• Start at 180 °C and increase in 5-degree steps
• Finer grind often needs 5–10 °C lower temperature
• In cold environments, raise starting temp by 5 °C

• Tinymight Official Website
• Tinymight 2 User Manual (PDF)
• Tinymight FAQ (Manufacturer)
• Warranty Registration & Conditions
• Official Tinymight Retailers
• Tinymight EU Shop – Accessories & Spare Parts

At the heart of the Mighty+ is Storz & Bickel's patented heating system combining convection and conduction. The chamber heats from the outside (conduction) while hot air simultaneously flows through the material (convection). This dual approach ensures even extraction from the first draw.

Compared to pure convection vaporizers like the Tinymight 2, the Mighty+ heats up a bit slower (~60 seconds to 180 °C), but vapor production stays consistent throughout the session. Airflow sits at 10 liters per minute — enough for deep draws with minimal resistance.

Booster & Superbooster

A double-click on the power button activates the Booster, raising temperature by 15 °C. This efficiently extracts remaining material near the end of a session without permanently changing the base temperature. Storz & Bickel calls the maximum level "Superbooster" — a practical feature other manufacturers lack.

The Mighty+ uses PEEK (polyether ether ketone) for its housing. PEEK comes from medical and aerospace industries: food-safe, heat-resistant, and far tougher than standard plastic. Where other vaporizers crack after a drop, a PEEK housing survives.

The filling chamber holds 1.4 cm³ and has a ceramic coating for wear resistance and easy cleaning — a damp cotton swab after every third session does the job. The cooling unit sits on top and uses a labyrinth airflow path that brings vapor to a comfortable temperature before it reaches the mouthpiece.

Storz & Bickel manufactures the Mighty+ entirely in Germany and certifies it under UL 8139 and IEC 60335-1 — safety standards rarely seen in the vaporizer industry.

The Mighty+ features an LC display showing current and target temperature simultaneously. Two soft-touch buttons (+/-) adjust temperature in 1-degree steps across a 40–210 °C range. The display reads well even in direct sunlight.

Compared to the VENTY (OLED display, Bluetooth app), the Mighty+ offers leaner app connectivity. Via Bluetooth it connects to the S&B Web App, where you can fine-tune the temperature and install firmware updates. That said, the device works perfectly without any app: two buttons on the display, pick your temperature, wait for the vibration — done.

A vibration alert signals when target temperature is reached. After one minute of inactivity, the Mighty+ shuts off automatically — saving battery and preventing overheating.

App & Firmware Updates

The S&B Web App runs directly in the browser — no app store download needed. After Bluetooth pairing, it shows real-time device temperature and allows precise adjustments. Firmware updates are offered automatically when available and install with one click.

Browser tip: Chrome (desktop and Android) works most reliably since the app uses the Web Bluetooth API. Safari and Firefox have limited or no Web Bluetooth support. On iOS, Bluefy (available in the App Store) provides a Web Bluetooth-capable browser as a workaround.

The Mighty+ houses two lithium-ion batteries totaling 3,300 mAh. In practice, expect 6 to 8 full sessions per charge, depending on temperature and draw behavior. That is less than the VENTY (5,940 mAh) but covers a full day for most users.

Charging runs through USB-C. With the Supercharger (15V / 3A, sold separately), the Mighty+ reaches 80 percent in roughly 40 minutes. Standard USB-C chargers work too, just slower. Passthrough charging is supported — vape while connected to the Supercharger.

At 242 grams and 8.0 × 14.0 × 3.0 cm, the Mighty+ is not a pocket device, but it fits a jacket pocket or small backpack. The weight gives it a premium feel that cheaper vaporizers lack.

The battery is not user-replaceable. Storz & Bickel offers battery replacement as a paid service.

Concentrates with the Mighty+

For waxes and oils, Storz & Bickel offers Liquid Pads – small stainless-steel mesh discs placed inside the filling chamber. The concentrate goes on top of the pad so nothing seeps into the device. A set of 8 costs around €10. The pads also fit inside dosing capsules together with a Concentrate Pad. Recommended temperature for concentrates: 190–210°C.

Battery Life in Practice

Storz & Bickel officially quotes around 90 minutes of use. In daily practice, that translates to 6 to 8 sessions at 180–190 °C. Heavy booster use or sessions above 200 °C bring the count closer to 5 or 6. For comparison, the VENTY with its 5,940 mAh battery lasts notably longer, though it weighs only 120 g less.

The two lithium-ion cells (3,300 mAh total) are permanently installed. When capacity drops after 2–3 years, Storz & Bickel offers paid battery replacement as a service — send the device in and expect it back within about two weeks.

The Mighty+ fully supports dosing capsules. These small stainless steel capsules are pre-filled and inserted as needed — practical on the go and keeps the chamber clean. An 8-capsule magazine is available as an accessory.

Other accessories: Wear & Tear Set (seals, screens, cooling unit parts), Mighty+ Case (hard shell), USB-C Supercharger, and the 14 mm water pipe adapter for bong sessions.

Cleaning

The cooling unit comes off without tools and soaks in isopropyl alcohol. Brush the chamber after each session. Every two to three weeks, Storz & Bickel recommends a thorough clean: disassemble the cooling unit, swap screens, wipe the chamber with a damp swab. The entire process takes under five minutes.

Tip: Collect used dosing capsules and batch-clean them in isopropyl alcohol — saves time and solvent.

Wear Parts & Replacement Costs

Storz & Bickel offers a Wear & Tear Set for around €30. It includes cooling unit parts, seals, screens, and a cleaning brush. Individual parts are also available: replacement screens (normal set, 6 pieces) for about €6, a complete cooling unit for about €18. Screens should be replaced every 3 to 6 months, the cooling unit as needed. Original parts are available from the Storz & Bickel online shop or authorized retailers.

The Mighty+ package includes:

• 1× Mighty+ vaporizer
• 1× USB-C charging cable
• 1× filling chamber tool with cleaning brush
• 3× normal screens + 3× coarse screens
• 1× quick start guide

The Supercharger (fast charger) is not included and must be purchased separately for around €40. Dosing capsules are also sold separately – the 40-capsule magazine with filling aid costs about €30.

Regular cleaning keeps the Mighty+ performing at its best and ensures pure flavor. Brush out the chamber after every session to remove loose residue. Clean the mouthpiece and vapor path weekly with isopropyl alcohol (90% or higher).

Cleaning Schedule

Common Mistakes to Avoid

• Never use water inside the chamber — only isopropyl or dry cleaning
• Do not use sharp metal tools in the vapor path
• Replace screens when draw resistance increases

Choosing the right temperature on the Mighty+ determines flavor, vapor density, and active compound profile. Lower temperatures (170–185 °C) emphasize terpenes and deliver mild, aromatic vapor. Higher temperatures (195–210 °C) produce thicker clouds and stronger effects.

Temperature Zones

Practical Tips

• Start at 180 °C and increase in 5-degree steps
• Finer grind often needs 5–10 °C lower temperature
• In cold environments, raise starting temp by 5 °C

The Mighty+ battery lasts several sessions with typical use. For maximum lifespan, keep the battery between 20% and 80% and avoid deep discharge. USB-C charging with a quality power adapter speeds up charging.

Battery Tips

• Do not leave on the charger permanently — unplug after 100%
• For replaceable batteries: use original or recommended cells
• Battery performance drops in cold — let it warm up before sessions
• Pass-through charging (if supported) allows use while charging

Both by Storz & Bickel with identical hybrid heating (210°C). The Mighty+ has a larger display and more battery. The Crafty+ is more compact and ~30 EUR cheaper but needs the app for full control.

• STORZ & BICKEL Support – MIGHTY+
• STORZ & BICKEL – Cleaning Guide
• MIGHTY+ Parts & Accessories
• Warranty Registration (+1 Year)